– Advantages:
+ Vina One Galvanized steel sheet is produced under a modern production system with innovative hot-dip galvanizing technology of NOF.
+ Vina One Galvanized steel sheet is high impact resistance to corrosion in different environments, it also meets the standards of ASTM (USA), JIS (Japan), BS (UK), AS (Australia) and TCVN (Vietnam).
– Applications:
+ Office Furnitures: shelves, signboards, billboards, etc.
+ House applications: push door, rolling door, wardrobe, waterspout, etc.
Vina One not only manufactures the products as our standard commercial specifications, but also make to customer’s orders.
| DIMENSIONS & TOLERANCES | |||
| DIVISION | Thickness (mm) | Width (mm) | |
| 0.16 ~ 3.20 | 600 ~ 1250 | ||
| Thickness & width tolerances allowances (mm) ) | Category |
Tolerances |
|
| Thickness | t≦0.40 | ±0.05 | |
| 0.40<t≦0.60 | ±0.06 | ||
| 0.60<t≦1.00 | ±0.07 | ||
| 1.00<t≦1.25 | ±0.08 | ||
| 1.25<t≦1.60 | ±0.09 | ||
| Width | -0, +7 | ||
| EQUIVALENT COATING MASS | |||
| Coating mass symbol (SI Units) |
Minimum average coating mass at triple spots (g/m2 ) |
Minimum average coating mass on both surfaces at single spot (g/m2 ) |
Equivalent coating thickness (mm) |
| Z06 | 60 | 51 | 0.013 |
| Z08 | 80 | 68 | 0.017 |
| Z10 | 100 | 85 | 0.021 |
| Z12 | 120 | 102 | 0.026 |
| Z14 | 140 | 119 | 0.029 |
| Z18 | 180 | 153 | 0.034 |
| Z20 | 200 | 170 | 0.04 |
| Z22 | 220 | 187 | 0.043 |
| Z25 | 250 | 213 | 0.049 |
| Z27 | 275 | 234 | 0.054 |
| CATEGORY, CHEMICAL COMPOSITION & MECHANICAL PROPERTIES | |||||||||||||
| Designation | Chemical Composition (%) | Mechanical Properties | |||||||||||
C |
Mn |
P |
S |
Yield strength
|
Tensile strength |
Elogation (%) | |||||||
| 0.25mm ≦t < 0.40mm | 0.40mm ≦t < 0.60mm | 0.60mm ≦t < 1.00mm | 1.00mm ≦t < 1.60mm | 1.60mm ≦t < 2.50mm | 2.50mm≦t | ||||||||
| SGCC | ≦ 0.15 | ≦ 0.80 | ≦ 0.050 | ≦ 0.050 | (205 ≦) | (270 ≦) | – | – | – | – | – | _ | |
| SGC570 | ≦ 0.30 | ≦ 2.50 | ≦ 0.20 | ≦ 0.050 | 560 ≦ | 570 ≦ | – | – | – | – | – | – | |
| TESTING CHARACTERISTICS | ||||||
| Shape | Bending test | |||||
| Category | Tolerance | Designation | Internal spacing | |||
| Bendability | 4 ≦ in any 2000 length | < 1.60 | 1.60 ≦ t <3.0 | 3.0 ≦ | ||
| Flatness | Wave | ≦12 | SGCC | 1t | 1t | 2t |
| Edge wave | ≦6 | SGC570 | – | – | – | |
| Central buckle | ||||||
| DIMENSIONS & TOLERANCES | ||
| DIVISION | ||
| Thickness (mm) | Width (mm) | |
| 0.16 ~ 3.20 | 600 ~ 1250 | |
| Width & Thickness Tolerances (mm) | ||
| Category | Tolerances | |
| Thickness | t ≦ 0.25 | ±0.04 |
| 0.25<t≦0.40 | ±0.05 | |
| 0.40<t≦0.60 | ±0.06 | |
| 0.60<t≦1.00 | ±0.07 | |
| 1.00<t≦1.25 | ±0.08 | |
| 1.25<t≦1.60 | ±0.09 | |
| Width | -0, +7 | |
| EQUIVALENT COATING MASS | |||
| Coating mass symbol (SI Units) |
Minimum average coating mass at triple spots (g/m2 ) |
Minimum average coating mass on both surfaces at single spot(g/m2 ) |
Minimum average a coating mass on 1 surface at single spot (g/m2 ) |
| Z001 | – | – | – |
| Z90 | 90 | 75 | 30 |
| Z120 | 120 | 90 | 36 |
| Z180 | 180 | 150 | 60 |
| Z275 | 275 | 235 | 94 |
| CATEGORY, CHEMICAL COMPOSITION & PHYSICAL PROPERTIES |
||||||||||||||
| Symbol of quality | Chemical Composition (%) | Physical Properties | ||||||||||||
| C | Mn | P | S |
Yield strength |
Tensile strength |
Elongation (%) | ||||||||
| CS Type A | ≦ 0.10 | ≦ 0.60 | ≦ 0.030 | ≦ 0.035 | 107 ~ 380 | (≧270 ~ ≦430) | ≧20 | |||||||
| CS Type B | 0.02 ~ 0.15 | ≦ 0.60 | ≦ 0.030 | ≦ 0.035 | 205 ~ 380 | (≧270 ~ ≦430) | ≧20 | |||||||
| SS33 [230] | ≦ 0.20 | ≦ 1.35 | ≦ 0.04 | ≦ 0.04 | ≧230 | ≧310 | ≧20 | |||||||
| SS80 [550] Class 1 |
≦ 0.20 | ≦ 1.35 | ≦ 0.04 | ≦ 0.04 | ≧550 | ≧570 | – | |||||||
| TESTING CHARACTERISTICS | ||||||||||||||
| Shape | Bending test | |||||||||||||
| Category | Tolerance | Designation | Internal spacing | |||||||||||
| Bendability | 4 ≦ in any 2000 length | CS | SS | |||||||||||
| Flatness | Wave | ≦12 | ≦ 1.0mm | >1.0mm; ≦2.0mm | >2.0mm | 230 | 255 | 275 | ||||||
| Z90 | 0 | 0 | 0 | 11/2 | 2 | 21/2 | ||||||||
| Edge wave | ≦6 | |||||||||||||
| Z120 | 0 | 0 | 0 | 11/2 | 2 | 21/2 | ||||||||
| Central buckle | Z180 | 0 | 0 | 0 | 11/2 | 2 | 21/2 | |||||||
| Z275 | 0 | 0 | 1 | 11/2 | 2 | 21/2 | ||||||||
| DIMENSIONS & TOLERANCES | |||
| Division | Thickness (mm) | Width (mm) | |
| 0.16 ~ 3.20 | 600 ~ 1250 | ||
| Width & Thickness Tolerances (mm) | Thickness | t≦0.25 | ±0.04 |
| 0.25<t≦0.40 | ±0.05 | ||
| 0.40<t≦0.60 | ±0.06 | ||
| 0.60<t≦1.00 | ±0.07 | ||
| 1.00<t≦1.25 | ±0.08 | ||
| 1.25<t≦1.60 | ±0.09 | ||
| Width | -0, +7 | ||
| EQUIVALENT COATING MASS | |||
| Coating mass symbol | Minimum average coating at triple spots (g/m2 ) |
Minimum average coating mass on both surfaces at single spot (g/m2 ) |
Minimum average a coating mass on 1 surface at single spot (g/m2 ) |
| Z100 | 100 | 90 | 40 |
| Z200 | 200 | 180 | 80 |
| Z275 | 275 | 250 | 110 |
| CATEGORY, CHEMICAL COMPOSITION & PHYSICAL PROPERTIES | |||||||
| Designation | Chemical Composition (%) | Physical Properties | |||||
| C | Mn | P | S |
Yield strength |
Tensile strength |
Elongation (%) |
|
| G250 | ≦ 0.12 | ≦ 0.50 | ≦ 0.040 | ≦ 0.035 | ≧250 | ≧320 | ≧25 |
| G300 | ≦ 0.30 | ≦ 1.60 | ≦ 0.100 | ≦ 0.035 | ≧300 | ≧340 | ≧20 |
| G350 | ≦ 0.30 | ≦ 1.60 | ≦ 0.100 | ≦ 0.035 | ≧350 | ≧420 | ≧15 |
| G550 | ≦ 0.20 | ≦ 1.20 | ≦ 0.040 | ≦ 0.030 | ≧550 | ≧550 | ≧2 |
| TESTING CHARACTERISTICS | ||||||
| Shape | Bending test |
|||||
| Category | Tolerance | Designation | Internal spacing | |||
| Bendability | 4 ≦ in any 2000 length |
Z100 | Z200 | Z275 | ||
| Flatness | Wave | ≦12 | G250 | 0 | 0 | 0 |
| Edge wave | ≦6 | G350 | 0 | 0 | 1t | |
| Central buckle | G550 | 1t | 2t | 2t | ||
